CPVC/PVC/KYNAR Out-of-Tank Bag Filter Systems
Pump Selection Guide — Previous Page
Self-Priming Sealless Magnetic Drive Pumps
Features polypropylene or Kynar sealless construction with permanent encapsulated impeller-magnet. Ater initial priming, it can run "dry" without pump damage. Shaft wear and replacement problems are minimized. For temperatures to 180°F. For higher temperatures,the pump is available in Kynar* (consult factory).
PUMP MOTOR MAX. PUMP
FLOW (GHP)		 MAX. PUMP
PRESSURE 		MOTOR HP
HP
SELF PRIMING SEALLESS MAGNETIC DRIVE PUMPS (Max. Temp. 180° F)
PMSP-218/KMSP-218 1080 15 1/4
PMSP-1035NT 2640 17 1/2
PMSP-1040NT 3120 24 3/4
PMSP-1040WT 3600 26 1
Sealless Magnetic Drive Pumps
Features Sealless polypropylene or Kynar construction with permanent encapsulated magnet. Shaft wear and replacement problems are minimized. For temperatures to 180°F. For higher temperatures the ½, ¾, and 1 hp pumps are available in Kynar*(consult factory).
PUMP MOTOR MAX. PUMP
FLOW (GHP)		 MAX. PUMP
PRESSURE 		MOTOR HP
HP
SEALLESS MAGNETIC DRIVE PUMPS (Max. Temp. 180° F)
PM-218 / KM-218 1200 16 1/4
PM-1040NT 3360 24 3/4
PM-1040WT 3800 26 1
Bearing Free Sealless Vertical Pumps
Features bearing-free sealless CPVC or Kynar construction with no metal contact. Vertical design requires a minimum of space and the twin-impeller feature allows the pump to be positions anywhere on tank flange, even outside the tank. Pumps are self priming when mounted inside tank. For temperatures to 200°F.
PUMP MOTOR MAX. PUMP
FLOW (GHP)		 MAX. PUMP
PRESSURE 		MOTOR HP
HP
SELF PRIMING SEALLESS VERTICAL IN-TANK PUMPS (Max. Temp. 200° F)
ZDX-1/2 B / ZKX-1/2B 2600 10 1/4
ZDX-3/4A 3600 12 3/4
ZDX-1D 4560 21 1
ZDX-2C 6000 27 2
* This pump is cpvc and polypropylene
Direct Drive Centrifugal Pumps
Model NR-1/3 and DHRC-1
Solid Noryl or CPVC construction with corrosion resistant Hastelloy-C shaft and your choice of leakproof mechanical seal . For temperatures over 160°F,the pump is mounted on a ball bearing pedestal. Change the system No. to "BOFC".
PUMP MOTOR MAX. PUMP
FLOW (GHP)		 MAX. PUMP
PRESSURE 		MOTOR HP
HP
DIRECT DRIVE CENTRIFUGAL PUMPS (See note 1 & 2)
NR-1/3 700 13 1/3
DHRC-12 3900 20 2
CDC-1 1/2X2X5-41/22 7600 34 3
1) Pump Seal is required
2) For temperature between 160° F, and 180° F. Specify optional Ball Bearing Pedestal.
Model CDC-1 ½ x 2 x 5-4 ½ (Not Illustrated)
Forged CPVC construction with integral impeller sleeve assembly. The pump is close coupled to the motor. For temperatures to 180°F, the pump is mounted on a ball bearing pedestal. Change the system number to "BOFC".

Motors: All Motors are TEFC. All Motors to 2 hp are equipped with waterproof switch and grounded cord. (Single phase motors greater than 1 HP are not provided with switch or cord).
— Previous Page
 
Sethco Division
800 Emlen Way
Telford, Pennsylvania 18969
Toll Free: 800-645-0500
Fax: 215-799-0920
E-mail: info@sethco.com 		© 2006 Sethco Division